Featured on all models unless otherwise specified:
- Dual band 802.11n Wifi (5Ghz added to previously only single band 2.4Ghz)
- Auto Lip sync delay (increased from 200ms to 500ms adjustment)
- RC Source Select (allows changing of an HDMI standby pass through source while the AVR is in Standby mode - 2015 and older models require powering on the AVR to change the pass through source)
- Playback of high resolution audio files (DSD 5.6 Mhz - increased from 2.8 Mhz) via USB and network
- DTS:X / DTS Neural:X pre-loaded (on SR7011)
- Audyssey iOS/Android phone app (est $20) - using the Audyssey mic, provides the ability to customize target curves, and save them, and LOAD back to AVP (ETA Fall 2016)
- Front Wide speakers and Audyssey DSX are no longer supported
- Web Control no longer available (to be replaced by new app capability with SAVE/LOAD via USB later this fall)
- Includes a HEOS module (SR7011 only) which will allow streaming the currently dozen music services (ie. Pandora, Spotify, TuneIn, AmazonMusic, DEEZER, Napster/Rhapsody, iHeartRadio, SiriusXM, SOUNDCLOUD, TIDAL, JUKE) using the HEOS iOS/Android app to the AVP as well as allow streaming 2CH sources to one or more HEOS wireless speakers placed around the home
Marantz NR1506 slim line receiver (cont'd from 2015). MSRP $499
Back panel picture of unit.
2016 Marantz AVR Owner's thread (NR1506/NR1607/SR5011/SR6011/SR7011)
Owner's manual of the NR1506:
http://us.marantz.com/us/Products/Pages/ProductDetails.aspx?CatId=AVReceivers&SubCatId=&ProductId=NR1506 Discrete Network chip reset (no settings lost).1 - With the AVR powered ON, select "Online Music" as the input source.
2 - Simultaneously press/hold the NR1506 "DIMMER" + "SOUND MODE" buttons on the front panel
3 - Hold the buttons for a few seconds until the display reads "Network Restart" and then release the buttons.
Try the above first when experiencing network issues before doing the full reset below which wiill result in the lose of all user settings as well as the Audyssey EQ.
Resetting the NR1506. Note that for microprocessor and network reset, all user and Audyssey setup settings will be wiped out. The SAVE/LOAD configuration steps should be performed beforehand to save user and Audyssey settings.
(1) Soft reset. Un-plug the power chord for approximately 10 minutes.
(2) Microprocessor reset. Also known as the factory reset.
- Turn OFF the unit
- Turn ON the unit and simultaneously press the M-DAX and TUNER PRESET CH+ buttons.
- Wait until the display starts flashing in 1 second intervals, then release the two buttons.
(3) Network reset.
- Turn OFF the unit
- Turn ON the unit and simultaneously press the TUNER PRESET CH+ and INTERNET RADIO buttons.
- Wait until the display starts flashing in 1 second intervals, then release the two buttons.
Marantz NR1607 slim line receiver. MSRP USD$699
Back panel picture of unit.
Owner's manual of the NR1607:
http://www.us.marantz.com/us/Products/Pages/ProductDetails.aspx?CatId=AVReceivers&SubCatId=0&ProductId=NR1607DAC used is the TI Burr Brown 1690.
What's new in the 2016 model compared to previous model (NR1606)?- DSD at 5.6Mhz
- 5GHz frequency support under WiFi (now dual band)
- New Audyssey phone app ($20USD) that will allow the user to check correction results, set target sound options, adjust frequency roll-off, set mid-range compensation controls and save, load, view and print results.)
- RC Source Select (allows changing of an HDMI standby pass through source while the AVR is in Standby mode - 2015 and older models require powering on the AVR to change the pass through source)
DTS:X with Neural:X upmixer firmware update released October 4, 2016.
Discrete Network chip reset (no settings lost).1 - With the AVR powered ON, select "Online Music" as the input source.
2 - Simultaneously press/hold the NR1607 "DIMMER" + "SOUND MODE" buttons on the front panel
3 - Hold the buttons for a few seconds until the display reads "Network Restart" and then release the buttons.
Try the above first when experiencing network issues before doing the full reset below (which would result in the lose of all user settings as well as the Audyssey EQ).
Resetting the NR1607. Note that for microprocessor and full network reset, all user and Audyssey setup settings will be wiped out. The SAVE/LOAD configuration steps should be performed beforehand to save user and Audyssey settings.
(1) Soft reset. Un-plug the power chord for approximately 10 minutes.
(2) Microprocessor reset. Also known as the factory reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the M-DAX and ZONE 2 SOURCE buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
(3) Full Network reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the ZONE 2 SOURCE and INTERNET RADIO buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
Marantz SR5011. MSRP USD$899.
Back panel picture of unit.
2016 Marantz AVR Owner's thread (NR1506/NR1607/SR5011/SR6011/SR7011)
DAC used is most probably the TI Burr Brown 1690.
Owner's manual of the SR5011:
http://us.marantz.com/us/Products/Pages/ProductDetails.aspx?CatId=AVReceivers&SubCatId=&ProductId=SR5011 What's new in the 2016 model compared to previous model (SR5010)?- DSD at 5.6Mhz
- 5GHz frequency support under WiFi (now dual band)
- New Audyssey phone app ($20, will allow the user to check correction results, set target sound options, adjust frequency roll-off, set mid-range compensation controls and save, load, view and print results.)
- RC Source Select (allows changing of an HDMI standby pass through source while the AVR is in Standby mode - 2015 and older models require powering on the AVR to change the pass through source)
DTS:X with Neural:X upmixer firmware update released October 4, 2016.
Discrete Network chip reset (no settings lost).1 - With the AVR powered ON, select "Online Music" as the input source.
2 - Simultaneously press/hold the SR-5011 "TUNER PRESET CH" + "/STATUS" buttons on the front panel
3 - Hold the buttons for a few seconds until the display reads "Network Restart" and then release the buttons.
Try the above first when experiencing network issues before doing the full reset below (which would result in the lose of all user settings as well as the Audyssey EQ).
Resetting the SR5011. Note that for microprocessor and full network reset, all user and Audyssey setup settings will be wiped out. The SAVE/LOAD configuration steps should be performed beforehand to save user and Audyssey settings.
(1) Soft reset. Un-plug the power chord for approximately 10 minutes.
(2) Microprocessor reset. Also known as the factory reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the M-DAX and ZONE 2 SOURCE buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
(3) Full Network reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the ZONE 2 ON/OFF and ZONE 2 SOURCE buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
Marantz SR6011. MSRP $1,399.
Back panel of unit:
2016 Marantz AVR Owner's thread (NR1506/NR1607/SR5011/SR6011/SR7011)
DAC used is most likely the TI Burr Brown 1690 .
Owner's manual of the SR6011 is here:
http://us.marantz.com/us/products/pages/ProductDetails.aspx?CatId=avreceivers&ProductId=SR6011What's new in the 2016 model compared to previous model (SR6010)?- Can process up to 11.1 channels!:D
- Has nine internal amps!:cool:
- DSD at 5.6Mhz
- 5GHz frequency support under WiFi (now dual band)
- New Audyssey phone app ($20, will allow the user to check correction results, set target sound options, adjust frequency roll-off, set mid-range compensation controls and save, load, view and print results.)
- RC Source Select (allows changing of an HDMI standby pass through source while the AVR is in Standby mode - 2015 and older models require powering on the AVR to change the pass through source)
- Cannot do Audyssey DSX or Front Wide speakers.
DTS:X with Neural:X upmixer firmware update released October 4, 2016.
Discrete Network chip reset (no settings lost).1 - With the AVR powered ON, select "Online Music" as the input source.
2 - Simultaneously press/hold the SR-6011 "TUNER PRESET CH" + "/STATUS" buttons on the front panel
3 - Hold the buttons for a few seconds until the display reads "Network Restart" and then release the buttons.
Try the above first when experiencing network issues before doing the full reset below (which would result in the lose of all user settings as well as the Audyssey EQ).
Resetting the SR6011. Note that for microprocessor and network reset, all user and Audyssey setup settings will be wiped out. The SAVE/LOAD configuration steps should be performed beforehand to save user and Audyssey settings.
(1) Soft reset. Un-plug the power chord for approximately 10 minutes.
(2) Microprocessor reset. Also known as the factory reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the M-DAX and ZONE 2 SOURCE buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
(3) Network reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the ZONE 2 ON/OFF and ZONE 2 SOURCE buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
For those interested in having external amps to power the main floor speakers and utilize the internal amps to power the Atmos height/ceiling speakers.
Amp Assign:
11.1Height Speakers:
4 Height SpeakersHeight Layout:
TF + TR (or whatever height speaker positions you are using)
Wide/HT 2:
Top Rear (or whatever 2nd height speaker position you are using)
Pre-out:
Front Marantz SR7011. MSRP $2,199.
Back panel of unit:
2016 Marantz AVR Owner's thread (NR1506/NR1607/SR5011/SR6011/SR7011)
Owner's manual for the SR7011 here:
http://us.marantz.com/us/Products/Pages/ProductDetails.aspx?CatId=AVReceivers&SubCatId=&ProductId=SR7011What's new in the 2016 model compared to previous model (SR7010)?- HEOS wireless multi-room sound system
- DSD at 5.6Mhz
- 5GHz frequency support under WiFi (now dual band)
- New Audyssey phone app ($20, will allow the user to check correction results, set target sound options, adjust frequency roll-off, set mid-range compensation controls and save, load, view and print results.)
- RC Source Select (allows changing of an HDMI standby pass through source while the AVR is in Standby mode - 2015 and older models require powering on the AVR to change the pass through source)
- Cannot do Audyssey DSX or Front Wide speakers.
DTS:X with Neural:X upmixer firmware installed at the factory.
Discrete Network chip reset (no settings lost).1 - With the AVR powered ON, select "Online Music" as the input source.
2 - Simultaneously press/hold the SR7011 "M-DAX" + "DYNAMIC EQ" buttons on the front panel
3 - Hold the buttons for a few seconds until the display reads "Network Restart" and then release the buttons.
Try the above first when experiencing network issues before doing the full reset below (which would result in the lose of all user settings as well as the Audyssey EQ).
Resetting the SR7011. Note that for microprocessor and network reset, all user and Audyssey setup settings will be wiped out. The SAVE/LOAD configuration steps should be performed beforehand to save user and Audyssey settings.
(1) Soft reset. Un-plug the power chord for approximately 10 minutes.
(2) Microprocessor reset. Also known as the factory reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the GAME and A-DSX buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
(3) Network reset.
Turn OFF the unit
Turn ON the unit and simultaneously press the MOVIE and MUSIC buttons.
Wait until the display starts flashing in 1 second intervals, then release the two buttons.
For those interested in powering the floor speakers with external amps and utilizing the internal amps of the SR7011 to power the Atmos/ceiling height speakers:
Amp Assign:
11.1Height Speakers:
4 Height SpeakersHeight Layout:
TF + TR (or whatever height speaker positions you are using)
Wide/HT 2:
Top Rear (or whatever 2nd height speaker position you are using)
Pre-out:
Front [/QUOTE]