AVS Discussions
  Go Down

JVC RS1000 / 2000 Anticipation Thread

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #45 on: October 01, 2018, 08:47:40 AM »
We don't have a dedicated RS3000 thread here so I'll post this here:



Seems like a very lucky German is getting the chance to look at a couple of the new JVC's for a day or two. I'm hoping he takes a couple contrast measurements!

Javs

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #46 on: October 01, 2018, 04:44:46 PM »
We don't have a dedicated RS3000 thread here so I'll post this here:



Seems like a very lucky German is getting the chance to look at a couple of the new JVC's for a day or two. I'm hoping he takes a couple contrast measurements!

Link?
JVC X9500 (RS620) | OZTS Majestic 120" 16:9 | Marantz AV7702 MkII | Emotiva XPA-7 | Rotel RMB-1555B | iNuke 3000DSP | DIY Javelin Audio TPL-150 L/C/R | DIY Faital MTM TPL-150 Surrounds | DIY Dolby Atmos MKII Modules | 30cf/Net Quad 18" Subs

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #47 on: October 01, 2018, 08:38:52 PM »
Dunno if you'll be able to view it or not. It's on cine4home's facebook group page. I think you need to be invited to see their page:

https://www.facebook.com/photo.php?fbid=10216860416613749&set=gm.1646460142125338&type=3&theater&ifg=1
« Last Edit: October 01, 2018, 08:45:52 PM by Dylan Seeger »

AVSMike

  • *****
  • 1021
Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #48 on: October 04, 2018, 06:24:18 AM »
Improvements that the new models offer over last years projectors.

Native 4K
Higher ANSI
Auto tone mapping with brightness slider
No E-shift noise
Reduced sync time
Greatly improved lens memory (explained below)
Improved lens
Improved image processing
Beefed up lens supports, so less image drift and more accurate lens memory
Vertical stretch with 4K 60P sources
USB firmware updates



Lens Memory on the RS540:

10 memories let you save:

Focus
Zoom
Shift



Installation Mode/Lens Memories on the RS1000/2000/3000/4500:

10 installation modes/memories let you save:

Focus
Zoom
Shift

Anamorphic Mode (A/B/C). Very useful with compression lenses which require zoom.

Installation Style: Not many situations for this, but I can think of a possible use.

Pixel Align: So you can have one pixel alignment for the 16x9 setting and a different if needed for the 2.35, or one for no anamorphic lens, and a different for with anamorphic lens

Screen Mode: Auto switch between two different screen materials. If using two screens and they are different material, this would be very useful.

Masking: Good for those changing aspect ratio movies.

Keystone: Not sure why you need to memorize this, when you should not even be using it.

Pincushion: Maybe you have a curved 2.35:1 screen and want Pincushion on with 2.35:1 lens memory, but you want it off with 16x9 lens memory. Another one, I think should never be used.

Aspect: Maybe you want 17:9 chip usage with 2.35:1 lens memory to get a little more brightness, but only 16x9 chip usage with 16x9 to have 1 for 1 mapping.


Also:

One of the memories can be selected to activate the 12V trigger: With a Motorized Sled for an Anamorphic Compression lens you could set a memory to zoom to screen width, engage Anamorphic mode, do the pixel adjust for that size, and then activate the 12V trigger to move the lens into place.

Easy to copy one mode to another position so you have a starting point for the next memory. Each memory name can be edited.

The same 10 discrete codes for the previous lens memory system are also used to control the 10 installation modes.
Mike Garrett
AV Science Sales
585-671-2968
mike@avscience.com

JVC, Sony, Epson, Marantz, Denon, Yamaha, Onkyo, Stewart, Seymour, Screen Innovations, Screen Excellence, DNP, Carada, Da-Lite, Vutec, Triad, SVS, Martin Logan, Def Tech, RBH, M&K and many other brands.

AVSCraig

  • *****
  • 2002
  • Home Theater Lover / Sales / Advice
    • AV Science, Inc
Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #49 on: October 04, 2018, 08:20:19 AM »
Lots of improvements over the previous generation. These are going to be great projectors !
Direct (585) 671-2972 8:30am - 4:30pm Pacific 
www.avscience.com  craig@avscience.com
We carry projectors, screens, speakers, receivers etc. !!
Twitter - @AVS_Craig

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #50 on: October 04, 2018, 08:56:45 AM »
Lots of improvements over the previous generation. These are going to be great projectors !

Great?

Maybe Kicka$$!

Maybe Kick Sony a$$!!

AVSMike

  • *****
  • 1021
Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #51 on: October 05, 2018, 12:29:16 PM »
Some were wondering if the lens in the 1000 and the 2000 would be the hand picked parts of the 640. Well the new 1000 and 2000 lens should outperform the 640 lens.
Mike Garrett
AV Science Sales
585-671-2968
mike@avscience.com

JVC, Sony, Epson, Marantz, Denon, Yamaha, Onkyo, Stewart, Seymour, Screen Innovations, Screen Excellence, DNP, Carada, Da-Lite, Vutec, Triad, SVS, Martin Logan, Def Tech, RBH, M&K and many other brands.

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #52 on: October 05, 2018, 12:35:01 PM »
Great news Mike! These new projectors can't get across the ocean fast enough! ETA is still 5-6 weeks?

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #53 on: October 07, 2018, 11:54:59 AM »
Getting the basement in my new house ready for the RS2000! Finally hung the screen today and I'm starting to put up black triple velvet material. The first 8 feet of the theater will be completely covered in this material. Floor, ceiling, walls, everything. The rest of the theater is freshly painted a medium grey color. Under the fluorescent lights it actually looks a shade purple (oops) hehe. I just installed new carpet for the room a few weeks ago too.

I'm trying to make the most of my first house. The basement isn't 100% ideal for a theater but it will be the best setup I've had so far. With the room constraints I actually had to jerry rig my EluneVision Reference 4K screen material to work with my old Carada screen frame. The EluneVision frame was too big to fit the screen and speakers width-wise in the room. In the photo you can actually see a tiny bit of the material on the underside of the frame. I need to cover that up, but it was necessary to tension the material properly. I need to build stands for the left and right speakers to go on either side of the screen. The center will go underneath the screen pitched up.

https://i.imgur.com/TcdWzBs.jpg
JVC RS1000 / 2000 Anticipation Thread




Only 7.1, maybe Atmos down the road. JTR Triple 8's for LCR, M&K surrounds and an Elemental Designs A7S-450 subwoofer. I had a Danely DTS-10 but sold it to help with closing costs for the new house.

Behind the theater is a utility room and (perfectly) shelves were installed on the wall in the there by the previous owner.  All I had to do was cut a small hole out for the projector lens. I'll probably get some trim and go around the hole to make it look a little more professional. (excuse the HDMI cord going through the hole temporarily haha)

https://i.imgur.com/3Ia2CwJ.jpg
JVC RS1000 / 2000 Anticipation Thread
« Last Edit: October 07, 2018, 05:45:23 PM by Dylan Seeger »

Javs

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #54 on: October 07, 2018, 11:34:43 PM »
^ Paint that rear wall black dude, thought you would know by now that the rear wall is a HUGE ANSI killer... Also given it looks like you dont have much throw at all in that room, even more important.

Gonna need a bigger hole?

The lens in the RS2000 looks to sit at least 3-4cm higher than the eshift units...
JVC X9500 (RS620) | OZTS Majestic 120" 16:9 | Marantz AV7702 MkII | Emotiva XPA-7 | Rotel RMB-1555B | iNuke 3000DSP | DIY Javelin Audio TPL-150 L/C/R | DIY Faital MTM TPL-150 Surrounds | DIY Dolby Atmos MKII Modules | 30cf/Net Quad 18" Subs

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #55 on: October 08, 2018, 03:12:19 AM »
@avsmike hi, USB firmware updates? that would be great, even more than 4k supports

AVSCraig

  • *****
  • 2002
  • Home Theater Lover / Sales / Advice
    • AV Science, Inc
Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #56 on: October 08, 2018, 08:40:56 AM »
@avsmike hi, USB firmware updates? that would be great, even more than 4k supports

Yes - the new projectors have USB for firmware updates.
Direct (585) 671-2972 8:30am - 4:30pm Pacific 
www.avscience.com  craig@avscience.com
We carry projectors, screens, speakers, receivers etc. !!
Twitter - @AVS_Craig

AVSCraig

  • *****
  • 2002
  • Home Theater Lover / Sales / Advice
    • AV Science, Inc
Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #57 on: October 08, 2018, 08:42:48 AM »
^ Paint that rear wall black dude, thought you would know by now that the rear wall is a HUGE ANSI killer... Also given it looks like you dont have much throw at all in that room, even more important.

Gonna need a bigger hole?

The lens in the RS2000 looks to sit at least 3-4cm higher than the eshift units...

Ya, painting the back wall black helped a lot in my room. Basically anything the screen shines directly at. Rosco Vleour Black worked wonders - straight from the can !
Direct (585) 671-2972 8:30am - 4:30pm Pacific 
www.avscience.com  craig@avscience.com
We carry projectors, screens, speakers, receivers etc. !!
Twitter - @AVS_Craig

AVSCraig

  • *****
  • 2002
  • Home Theater Lover / Sales / Advice
    • AV Science, Inc
Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #58 on: October 08, 2018, 08:44:22 AM »
Getting the basement in my new house ready for the RS2000! Finally hung the screen today and I'm starting to put up black triple velvet material. The first 8 feet of the theater will be completely covered in this material. Floor, ceiling, walls, everything. The rest of the theater is freshly painted a medium grey color. Under the fluorescent lights it actually looks a shade purple (oops) hehe. I just installed new carpet for the room a few weeks ago too.

I'm trying to make the most of my first house. The basement isn't 100% ideal for a theater but it will be the best setup I've had so far. With the room constraints I actually had to jerry rig my EluneVision Reference 4K screen material to work with my old Carada screen frame. The EluneVision frame was too big to fit the screen and speakers width-wise in the room. In the photo you can actually see a tiny bit of the material on the underside of the frame. I need to cover that up, but it was necessary to tension the material properly. I need to build stands for the left and right speakers to go on either side of the screen. The center will go underneath the screen pitched up.

https://i.imgur.com/TcdWzBs.jpg
JVC RS1000 / 2000 Anticipation Thread




Only 7.1, maybe Atmos down the road. JTR Triple 8's for LCR, M&K surrounds and an Elemental Designs A7S-450 subwoofer. I had a Danely DTS-10 but sold it to help with closing costs for the new house.

Behind the theater is a utility room and (perfectly) shelves were installed on the wall in the there by the previous owner.  All I had to do was cut a small hole out for the projector lens. I'll probably get some trim and go around the hole to make it look a little more professional. (excuse the HDMI cord going through the hole temporarily haha)

https://i.imgur.com/3Ia2CwJ.jpg
JVC RS1000 / 2000 Anticipation Thread


Looks to be a really good setup Dylan ! And I love having the projector in another room. Congratulations on the new theater !  :)
Direct (585) 671-2972 8:30am - 4:30pm Pacific 
www.avscience.com  craig@avscience.com
We carry projectors, screens, speakers, receivers etc. !!
Twitter - @AVS_Craig

Re: JVC RS1000 / 2000 Anticipation Thread
« Reply #59 on: October 08, 2018, 08:57:43 AM »
^ Paint that rear wall black dude, thought you would know by now that the rear wall is a HUGE ANSI killer... Also given it looks like you dont have much throw at all in that room, even more important.

Gonna need a bigger hole?

The lens in the RS2000 looks to sit at least 3-4cm higher than the eshift units...

That's my plan, just haven't gotten around to it yet.

  Go Up