AVS Discussions
Projection Screens => 2.35:1 Screens / lenses => Topic started by: ed weinman on August 26, 2021, 07:45:08 PM
-
I purchased the Carada screen some time ago when Carada was still in business. The price was all that I could afford at the time and I've been living with the screen flaws since purchase. I was just wondering if it is possible to remove the Carada frame, replace the screen with, let''s say, a Stewart, then replace the Carada frame?
I don't know if this is possible. I also don't know how to remove the frame if it is.
Any suggestions would be appreciated.
-
I purchased the Carada screen some time ago when Carada was still in business. The price was all that I could afford at the time and I've been living with the screen flaws since purchase. I was just wondering if it is possible to remove the Carada frame, replace the screen with, let''s say, a Stewart, then replace the Carada frame?
I don't know if this is possible. I also don't know how to remove the frame if it is.
Any suggestions would be appreciated.
Ed, check with Ralph Potts. He has the Carada masking with a Stewart Screen.
-
Ed, check with Ralph Potts. He has the Carada masking with a Stewart Screen.
David, how do I contact Ralph?
-
David, how do I contact Ralph?
I sent him and email and asked him to chime in here. He should post something in the next 24 hours (or less).
-
I purchased the Carada screen some time ago when Carada was still in business. The price was all that I could afford at the time and I've been living with the screen flaws since purchase. I was just wondering if it is possible to remove the Carada frame, replace the screen with, let''s say, a Stewart, then replace the Carada frame?
I don't know if this is possible. I also don't know how to remove the frame if it is.
Any suggestions would be appreciated.
Hi Ed. i am checking to see what I can do for you.
-
Mike/David
Thank you both very much.
Ed
-
Greetings,
Hi Ed, I am using the Masquerade masking system with a Stewart Studiotek 130 G3 screen. I ordered the Masquerade after I already had the Stewart and it was built specifically to the dimensions of the Stewart.
What you are asking is certainly possible as long as the fixed frame Stewart you're ordering matches the dimensions of the screen you're currently using with the Carada.
Good Luck!
Best,
Ralph
-
Greetings,
Hi Ed, I am using the Masquerade masking system with a Stewart Studiotek 130 G3 screen. I ordered the Masquerade after I already had the Stewart and it was built specifically to the dimensions of the Stewart.
What you are asking is certainly possible as long as the fixed frame Stewart you're ordering matches the dimensions of the screen you're currently using with the Carada.
Good Luck!
Best,
Ralph
Thanks Ralph. I thought that was what you did, but I wasn't 100% sure. I appreciate you coming on over and helping :)
-
Ralph, Hi
Thanks for the reply. I have a million questions but I'll limit it to just a few (for now!). The Carada fame and screen were installed by professionals because I had (have) no idea of what I was or could do.
Can the Carada frame be simply lifted off the wall and placed somewhere else?
Can the Carada screen also be lifted off in similar fashion?
Is the Carada frame even complete so that it does not come off and fall to pieces? Is the frame very heavy or can one person just lift and install it over the new screen?
(I have all my amps, etc. under the screen and will have to disassemble them before anything. I also have two Magnepan towers that will probably have to be moved but I believe I can do it myself.)
Ralph, I'd appreciate any info you can give me.
Thanks, in advance and David, thanks again
Ed
-
Ralph, Hi
Thanks for the reply. I have a million questions but I'll limit it to just a few (for now!). The Carada fame and screen were installed by professionals because I had (have) no idea of what I was or could do.
Can the Carada frame be simply lifted off the wall and placed somewhere else?
Can the Carada screen also be lifted off in similar fashion?
Is the Carada frame even complete so that it does not come off and fall to pieces? Is the frame very heavy or can one person just lift and install it over the new screen?
(I have all my amps, etc. under the screen and will have to disassemble them before anything. I also have two Magnepan towers that will probably have to be moved but I believe I can do it myself.)
Ralph, I'd appreciate any info you can give me.
Thanks, in advance and David, thanks again
Ed
Greetings,
Ed, the Masquerade is a masking system. So, try not to think of it terms of being a frame. It is mounted to the wall over your current screen.
It's primary pieces are the top header (which contains the motor assembly) and bottom. These contain the masking panels (upper and lower). There are rails, one per side, that connect the top and bottom. When the motor is operated the masking is raised (from the bottom) and lowered (from the top) along the rails. The masking material itself is on rollers that run the length of the bottom/top pieces.
There are left/right covers that slide into the top/bottom pieces which cover the rails and match the top/bottom to provide the appearance of the framed enclosure.
The top header is mounted to the wall with a bracket that supports it weight. Lifting it off of the bracket requires two people. The bottom piece is light enough to be handled alone. The side covers are easy to remove by using the palm of your hand to push it out (to the right for the right hand side and to the left for the left hand side) at the top and bottom so you can gain access to the rails which are connected to the bottom piece by nuts.
I installed mine and believe that I still have the assembly instructions via PDF. I will check and post back.
Regards,
-
Greetings,
Ed, attached is the assembly instructions for the Carada Masquerade masking system. This will answer many of your questions as well as allow you to disassemble and reinstall the system.
Best of luck!
Regards,
-
Greetings,
Ed, attached is the assembly instructions for the Carada Masquerade masking system. This will answer many of your questions as well as allow you to disassemble and reinstall the system.
Best of luck!
Regards,
You're the best Ralph. Awesome work buddy!
-
Ralph,
I looked at the manual setup for the frame and I do not think I can do it.
Question:
Can the frame top be removed by two people simply without having to do any hardware?
The same question for the bottom and side panels?
I've taken up alot of your time as well as David and Mike, and I really appreciate all the help/suggestions that have been offered to me. (Being 79 is not a happy event!)
Mike was looking into the Stewart situation for me but I think this whole event will be costly and, unless there is some company in Santa Ana ad/or Orange County, CA that whould be willing to do all this for me...I am too scared to attempt anything on my own. I've already emailed Mike and would deeply want to thank you, Mike and David for all your help.
In deep appreciation,
Ed Weinman
-
You're the best Ralph. Awesome work buddy!
Greetings,
If you reach out, you know that I am there Dave..anytime. ;)
Regards,
-
Ralph,
I looked at the manual setup for the frame and I do not think I can do it.
Question:
Can the frame top be removed by two people simply without having to do any hardware?
The same question for the bottom and side panels?
I've taken up alot of your time as well as David and Mike, and I really appreciate all the help/suggestions that have been offered to me. (Being 79 is not a happy event!)
Mike was looking into the Stewart situation for me but I think this whole event will be costly and, unless there is some company in Santa Ana ad/or Orange County, CA that whould be willing to do all this for me...I am too scared to attempt anything on my own. I've already emailed Mike and would deeply want to thank you, Mike and David for all your help.
In deep appreciation,
Ed Weinman
Greetings,
Ed, as you can see by the instructions, the top and bottom are connected by the rails. Removal of the nuts that hold them together as well as release of the straps that raise and lower the bottom mask (in addition to removing the small wood screws) will allow taking the top and bottom off of the wall. The side pieces simply slide off (see that instructions).
If someone helps you it can absolutely be done with little problem.
Regards,
-
Can anyone suggest a home theater installer or anyone else in my area (Santa Ana/Orange County, Ca) that would be willing and have some knowledge of what to do?
I'd really appreciate it.
-
Ralph,
I believe you are describing the Masquerade frame that is 16.9 due to your description of the top and bottom going up and down.
I have the 2.35.1 version with the top and bottom fixed and only the sides going in and out for the different ratios.
Does this change things?
-
Ralph,
I believe you are describing the Masquerade frame that is 16.9 due to your description of the top and bottom going up and down.
I have the 2.35.1 version with the top and bottom fixed and only the sides going in and out for the different ratios.
Does this change things?
It should be the same concept (in theory), but the side masking may be two individual units. You'd have to remove those and see what screen is underneath.
-
Here's an article discussing the system: https://www.projectorreviews.com/carada-2/carada-masquerade-cih-review-a-motorized-masking-system-for-your-projector-screen/
It looks to be the same as Ralph's, but instead of the rails being on the left and right, they are on the top and bottom. Same concept but turned on its side.
-
Here's an article discussing the system: https://www.projectorreviews.com/carada-2/carada-masquerade-cih-review-a-motorized-masking-system-for-your-projector-screen/
It looks to be the same as Ralph's, but instead of the rails being on the left and right, they are on the top and bottom. Same concept but turned on its side.
Yes. Works the same. Panels are just traveling horizontally, rather than vertically. Frame is still 6.25" in width. Carada had a cheaper frame that they used under the masking system, but I can't remember the name of the screen frame. That was what was used if you bought it all at the same time. You could also just buy the carada masking system to cover your existing frame. Just had to size accordingly.
I know when I designed stewart screens to go under the masking system, I would use an odd screen ratio, so that the screen fabric extended well behind the masking system, so that you did not see the frame behind the masking trim.
-
Mike/David
...again, my thanks
Ed
-
...just an update: I purchased the Stewart GrayHawk G4 wall screen plus...the installer will do the following:
1) remove the Carada Frame
2) remove the Carada Screen
3) install the Stewart Screen
4) reinstall the Carada Masking System
I'v lived with the Carada screen for 7 years knowing it's problems and can't wait for the Stewart (the company rep. stated it would be shipped October 8th and that I should get it possibly the following week)...
-
...just an update: I purchased the Stewart GrayHawk G4 wall screen plus...the installer will do the following:
1) remove the Carada Frame
2) remove the Carada Screen
3) install the Stewart Screen
4) reinstall the Carada Masking System
I'v lived with the Carada screen for 7 years knowing it's problems and can't wait for the Stewart (the company rep. stated it would be shipped October 8th and that I should get it possibly the following week)...
Awesome...take pictures of the install. I'm curious of how this will work out. You'll love the Stewart screen...they are the best!
-
David,
I'd love to take pictures but, at 79, and not up to the latest tech., I have no way to do it!!
Sorry,...and, yes, I do hope to see a remarkable improvement.
Ed
-
David,
I'd love to take pictures but, at 79, and not up to the latest tech., I have no way to do it!!
Sorry,...and, yes, I do hope to see a remarkable improvement.
Ed
LOL Ed. I get it. Then again, my Mom will be 79 next month and my sister calls her a technology whore. Always has the latest phone :)
-
David,
Well, then, she's lucky!!
Question: the frame is the Carada Masquerade Frame is Cinemascope with a remote control for the side panels. Can the moter be oiled or lubed or some such thing? After all, I've been using it for seven years!
Thanks, in advance
-
Resolved:
AV Science, Inc. told me to ask the installer, upon reinstalling the Carada frame, to first lubricate on the pullies and channels that the parts slide in. I assume that this will make it less of a strain for the motor to operate.
-
The remote for my Carada Masquerade 2:35.1 is sick and needs a doctor...some of the buttons do not work and I don't know how to fix it. I've tried to find an alternate remote but was unsuccessful. There appears to be a very, very small screw on the back side but I've tried three screw drivers but to no avail. (I thought this would open the remote).
Is there an alternative remote that would work?
Any help would be appreciated.